18 not categorized PORSCHE 924 S RS REAR FENDERCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 914 1970-76 (includes uncategorized and accessory items) FVD504911RSR These fender flares are made of metal sheet set (4pcs): - fender flare front left - fender flare front right - fender flare rear left - fender flare rear right
$5,402.10
Make a selection FVD911503185186 This seal kit consists of original part # 911 503 185 00 (left) and 911 503 186 00 (right). The set can be used on the trailing edge of the front fender at the cowl just below the windshield. It is also used under the back of the rear quarter panel where it meets the bumper side panel. Genuine part sourced from Porsche ag in Germany to ensure quality, reliability and precise fitment. Sold as a set. 1 set is necessary for front fenders and one set is necessary for the rear. Please note: this is the thinner width. This is not the thicker width from the SC models.
$14.93
Make a selection MIT1408 Achieve the great look of the rare 916 factory prototype for your 914. Fiberglass bolt-on will also reduce weight. Primed and ready for painting to match your 914. The smooth clean appearance is also aerodynamically efficient! (for stock fenders. Bumper must be slightly modified to fit GT flares) General Fitment914 1970-76
$395.00
Make a selection
$385.00
Make a selection
$385.00
Make a selection 10050330000 This 9 inch front and 11 inch rear steel fender flare set is made in Germany, we offer a complete line of replacement bodywork to complement the entire Porsche model range. Sold individually. 1 necessary per car. Please note: for conversions, these flares will allow you to run 9 wide tires in the front and 11 wide in the rear. For the 964 / 965 models the torsion bar cut out must be filled. Due to variances in production at the factory, age, accident damage or rust, each part may require trimming and or adjustment for perfect fitment.
$1,648.90
Make a selection MIT1408F Achieve the great look of the rare 916 factory prototype for your 914. Fiberglass bolt-on will also reduce weight. Primed and ready for painting to match your 914. The smooth clean appearance is also aerodynamically efficient! Lead time of 4-8 weeks. General Fitment914 1970-76
$365.00
Make a selection 10050305503GFK Made in europe by one of the manufacturers to Porsche. Extremely high-quality grp (glass-reinforced plastic) rear bumper that includes every detail for a perfect fit. Features: - produced by an OEM manufacturer. - highest quality standards. - perfect fitment. - lightweight 9.7 lbs. (4.4 kg) - made of high strength, grp (glass-reinforced plastic) sold individually. 1 necessary per car. Please note: this only fits in conjunction with widebody / rsr rear fenders, part # FVD503930001 . Please provide us with the year / model. These are high quality parts that take time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world. All grp products must proper...(choose a part on the right to read more)
$1,265.00
Make a selection AA500 Available only from Automobile Atlanta, this kit consists of parts that we use in our restoration shop without going overboard. General Fitment914 1970-76
$629.26
Make a selection 91450303211A This is the rear part of the right front fender where the fender attaches to the cowl. great for repairing the rust in this area and joins our cowl repair panel. No more fabrication! General Fitment914 1970-76
$52.47
Make a selection 91450303111A This is the piece for the repair of the rear of the 914 front fender where it attaches to the cowl. we also have the cowl repair panel available General Fitment914 1970-76
$52.47
Make a selection AA500A Our rubber kits are for the perfect restoration. Available only from Automobile Atlanta, this kit consists of everything we use in our restoration shop. General Fitment914 1970-76
$1,012.23
Make a selection 916BODYKIT
General Fitment914 1970-76
$2,283.80
Make a selection SP100 After years of use all factory 914 coil springs sag. Look for three inches of tire to show between the wheel and the fender lip to ascertain if the springs are sagging or not. (also look for adjustible spring plates. Optionally installed they may have been set too low) 100 lb springs are the choice for all street and hot street driving applications. heavier than the stock originals, they will also cause the 914 to turn in better. we recommend these springs specifically for 914-6 and six-conversion cars. Sold as a pair. General Fitment914 1970-76
$156.00
Make a selection 91450390800
$655.60
Make a selection AA914501 This is a perfect fit kit to reconstruct the complete right rear inner fender well battery tray suspension console engine shelf area that every Porsche 914 suffers from the battery leaking acid. i am always asked about reconstructing the rusted away battery area, referred to some as the "914 hell hole" (hate that term applied to a 914 lol) so have finally decided to list the whole kit on e bay so you can see how the parts interact. (support was painted for contrast buy you will get a brand new one) moderately installed by the home hobbyist or welder/body man, it will return your car to its original configuration and strength. all parts manufactured by us in michigan based on original factory nos parts for ...(choose a part on the right to read more)
$1,100.00
Make a selection 22050419200KEV
$894.30
Make a selection 22050419100KEV
$894.30
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |